Wind is the worst of the common recording noises, because it does not sound like a noise. A fan hisses, a fridge hums, and both are obvious. Wind arrives as a low rumble that you feel more than hear, and it moves. A gust lands in the middle of a sentence and takes the sentence with it.
That shapes what you can fix afterwards. The steady part can be turned down. The gusts usually have to be cut, or the line has to be recorded again. This guide does both, in the order that costs you the least.
What wind actually does to a recording
Wind is moving air hitting the microphone’s diaphragm. The diaphragm reads that as a very loud, very low sound, so it adds a rumble that sits under the voice, mostly below 100 Hz, and often much louder than the voice itself.
Two things follow from that:
- Steady wind sounds like a low rumble or a rumble with a slow pulse. It behaves like any other steady noise, so a noise remover can reduce it.
- Gusts arrive suddenly, push the diaphragm hard, and can overload the microphone’s input. When that happens the voice is not just buried, it is distorted, and distortion cannot be removed by any tool.
That second case is why the first step below matters more than every step after it.
1. Stop the wind at the microphone
This is the only step that keeps the voice exactly as it was, and it costs nothing to try.
- A furry windscreen, not foam. Foam handles breath up close. Outdoors you want the fake fur cover, the one people call a deadcat, over the mic or over the camera’s built-in mic. It slows the air before it reaches the diaphragm.
- Get the mic out of the airflow. Clip it low on the chest, behind the talent’s shoulder, or under the chin, so the body blocks the wind. Aim the back of the mic, the side facing away from the mouth, into the wind.
- Shield the mic, do not fight the weather. Recording from behind a wall, a car, or the corner of a building removes more wind than any setting.
- Turn on the low cut if your recorder has one. Most recorders and interfaces label it as a high-pass filter or low cut, and 80 to 100 Hz is where it usually starts. It costs you nothing on a voice.
If the take is already recorded and the wind was heavy, steps 2 to 5 are the recovery.
2. Drop the video straight into Gleam Audio
Since version 2.0, every tool takes video files for their sound. Drop the mp4, mov, mkv, webm or avi on the window, or click Open Files…. You do not need to export an audio track first, and the picture is never touched.
The result is audio only, saved as m4a, or in the format you pick in Convert.
Gleam Audio runs on macOS, Windows and Linux, does the work on your own computer, and is free for personal use up to 20 files a week. Nothing is uploaded.
3. Run Remove noise with Strength low
Remove noise is the speech cleanup tool. Pick it in the sidebar, then set Strength.
Wind is broadband, so a high setting removes a lot of the voice along with it. Start at the bottom of the range and raise it only until the gaps between sentences go quiet. Version 2.1 added a Before and After switch on every finished file, so you can hear the original against the result while it plays and pick the lower setting when the two are close.
This is the same trade-off that makes a heavily cleaned voice sound robotic, and wind is where it shows up fastest. If the noise in your file is a fan, traffic or room tone instead of wind, how to reduce background noise in a video covers that case with the same steps.
4. Cut the gusts that no setting fixes
A gust is a few seconds long and usually sits over a word. Lowering Strength until the gust is gone leaves the whole file hissy, and raising it until the gust is gone eats the speech. Neither is worth it.
Take those seconds out instead. Cut shows the file as a picture of the sound, so a gust is visible as a dark block of low end before you play it, and you can trim it out. Cut works on one file at a time, so do the worst gust first and listen again before you take out the next.
If the gust landed on a line you need, record the line again and cut it in over the gap. That is more work than a filter, and it is the only version that sounds right.
5. If a low rumble is left, high-pass it
Noise removal lowers the rumble. It rarely deletes it, and the part still down there is the part you can see in the picture of the sound as a solid band at the bottom.
Gleam Audio’s nine tools do not include an EQ, so this last step happens in your video editor. Every editor has a high-pass filter in its audio effects, sometimes called low cut. Set it to 80 Hz, raise it to 100 or 120 if the rumble is still there, and stop as soon as the voice sounds thin.
From a terminal, ffmpeg does the same thing:
ffmpeg -i clip.m4a -af "highpass=f=90" clip-clean.wavf=90 is the corner frequency in Hz. ffmpeg applies a two-pole filter by default, which is a gentle slope, so a steep cut is not on the table without more work.
6. Put the sound back on the timeline
Import the cleaned file, drop it on an audio track lined up with the start of the original clip, and mute the original clip rather than deleting it, so you can switch back while you compare.
Nothing in the chain changes the length. Removing noise and filtering both keep the file the same length, and if you cut a gust out, the seam is where you put it. Play the first sentence and check one lip sync point; if it drifts, the cleaned file started from a different point than the clip.
Export the video with the new audio track. The remove audio from a video guide covers the reverse case, taking the sound out and leaving silence.
When it won’t help
- The recording clipped. Wind that pushed the meter into the red distorted the voice, and no remover restores it. Listen to one loud syllable: if it crackles or sounds torn, record the take again.
- The wind sits at the same pitch as the voice. Male voices reach down to about 85 Hz, so a cut that removes the rumble takes the bottom of the voice with it.
- There is more wind than voice. If the gust covers the whole syllable, noise removal has nothing to separate the two, and the result sounds like a whisper in a storm.
- The take is music, not speech. Remove noise is tuned for speech. On music it takes out more than you want, which the known limitations page says plainly.
- A phone recording with an uncovered mic. Phone mics sit on the outside of the case, right in the wind, and the recorder has no low cut. That file starts one step behind.
Takeaways
- Wind is a low rumble plus gusts. The rumble is like any steady noise; the gusts are not.
- A furry windscreen and a mic out of the airflow remove more wind than any setting afterwards.
- Since 2.0, Gleam Audio takes the video file as it is and saves audio only.
- Run Remove noise at a low Strength, cut the gusts you cannot clean, and high-pass what is left in your editor.
- A clipped take cannot be repaired. Record it again.